J1939 Doctor Diagnostic ToolSelf-contained J1939 diagnostics tool with physical network and data analysis on your phone, tablet, PC, or MAC.The J1939 protocol is increasingly being adopted in marine applications, providing monitoring and control for engines, propulsion systems, generators, and electrical networks. To support this...

LED Battery TesterSpecifically for all 12 Volt DC batteries.

Prop Master Prop Stop Propeller StopFeatures: Simple to use Securely holds prop during changing Makes prop-changing safer Brightly colored for greater visibility (Remember to remove propeller stop before using your boat) WARNING: This product can expose you to chemicals which are known to the...

Prop Master Propeller WrenchThe Prop Master™ is the original molded propeller wrench.This 1-1/16" six point socket style prop wrench is made of high tensile strength, indestructible nylon. It is totally resistant to fuel, sun, salt water, and other chemicals. The Prop Master™ is less...

Stainless Steel Bottle Opener with Brushed Finish Corrosion resistant investment cast 316 stainless steel bottle opener wall mounts with two #6 FH fasteners (not included).WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects...

Add-A-Snap - White - 2-1/2" For use with canvas or nylon boat covers, the Add-A-Snap allows you to easily add length on hard to reach snaps from shrunken material. Nickel plated brass/nylon.WARNING: This product can expose you to chemicals which are known to the State...

Add-A-Snap - White - 1-1/2" For use with canvas or nylon boat covers, the Add-A-Snap allows you to easily add length on hard to reach snaps from shrunken material. Nickel plated brass/nylon.WARNING: This product can expose you to chemicals which are known to the State...

Thru-Hull Installation Tool Thru Hull Installation ToolThe Concept:THT-530 makes the installation of standard GROCO thru-hull fittings possible by a single installer.  Slide the thru-hull fitting, flanged end first, over the tool.  (It will stop at the proper step.)  Tie a length of monofilament to the...

Marine Formula™ 5oz AerosolMarine Formula™ is a specially formulated patented mixture that cleans and removes adhesives and sealants on and inside the boat. Use Marine Formula™ to clean up and remove these common marine adhesives and sealants. Quick Guide (pdf)

AT-6031 Metal Bond AdhesiveAT-6031 is a 10-to-1 metal bonding adhesive. It has high viscosity (cures in 10–12 minutes), has a 6-minute working time, and develops working strength in 40 minutes. AT-6031 develops more than 2,500 lbs. (psi) of tensile strength on most metal surfaces,...

Portable Rope Cutting GunPanther’s portable Rope Cutting Gun is ideal for boat, camper and home use. Lightweight (1.5 lbs), the handle fits in the palm of your hand with easy finger pull operation. It makes quick clean cuts in all types of synthetic ropes,...

Snap Tool Multi-KeyA deck plate with attitude! Handy Universal Stainless Steel Strong Perfect for: Fishing Hiking Climbing Boating Biking Camping Sailing Tailgating RV Brochure (pdf)

Prop Wrench Set - Fits 17/32" to 1-1/4" Prop NutsMultiple socket sizes for all prop maintenance. Offers multiple sockets to fit from 17/32" to 1-1/4", allowing consumers to service multiple props Built of durable plastic WARNING: This product can expose you to chemicals which...

AT-5B Large Black Nylon Wire Tie Mount - Qty. 500The AT-5 tie mount is designed to be set into wet resin during the hull lay up or bonded with our acrylic adhesives. It's designed for a #5 wire tie and has an average pull...

AT-5 Large White Nylon Tie Mount - Qty. 500The AT-5 tie mount is designed to be set into wet resin during the hull lay up or bonded with our acrylic adhesives. It's designed for a #5 wire tie and has an average pull strength...

1.5" Tall Stainless Stud w/#10 x 24 ThreadUtilize the same base as the 1.4" x 20 studs but with a smaller threaded stud inserted into the base. These studs are ideal for mounting wire clamps and securing items which require a smaller stud diameter....

.75" Tall Stainless Stud w/#8 x 32 ThreadOur Small Stainless Steel Panel Studs have a wide range of uses. Originally they were used for mounting on the backside of dash panels for mounting to the console. Now they are used for securing a wide...

Footman's Strap MountThe Footman's Strap Mount is designed to be bonded with AT-4020 Acrylic Adhesive. This strap mount is 3.25" long and 1" wide and holds up to a 1.3" max strap width. This strap is incredibly strong, paintable, and is rated for over...

Footman's Strap MountThe Footman's Strap Mount is designed to be bonded with AT-4020 Acrylic Adhesive. This strap mount is 3.25" long and 1" wide and holds up to a 1.3" max strap width. This strap is incredibly strong, paintable, and is rated for over...

Adhesive Dispensing GunThe AT-300 Adhesive dispensing gun has a 1:1 plunger for use with AT-2010 and AT-4020 50ml cartridges (sold separately) When using AT-6030 adhesive it requires AT-12 (10 to 1 plunger). Replacement plungers are also available.

Acrylic AdhesiveCAN NOT SHIP AIR,UPS GROUND ONLYAT-4020 is a specially formulated adhesive for holding all our parts with little or no sagging in vertical or overhead applications. Cures in 10 - 12 minutes and has working strength within 40 minutes. AT-4020 is recommended for...

Black Nylon Wire Tie MountThe AT-3 tie mount is smaller for panel and other small space applications. This part is molded in black nylon and is sized for a #3 wire tie with a maximum width of .20". Average pull strength is about 50...

Black Nylon Wire Tie MountThe AT-5 tie mount is designed to be set into wet resin during the hull lay up or bonded with our acrylic adhesives. It's designed for a #5 wire tie and has an average pull strength of 150 lbs. It's...

Marine Formula™ 10oz AerosolMarine Formula™ is a specially formulated patented mixture that cleans and removes adhesives and sealants on and inside the boat. Use Marine Formula™ to clean up and remove these common marine adhesives and sealants. Quick Guide (pdf)

Black Nylon Wire Tie MountThe AT-5 tie mount is designed to be set into wet resin during the hull lay up or bonded with our acrylic adhesives. It's designed for a #5 wire tie and has an average pull strength of 150 lbs. It's...

White Nylon Wire Tie MountThe AT-3 tie mount is smaller for panel and other small space applications. This part is molded in white nylon and is sized for a #3 wire tie with a maximum width of .20". Average pull strength is about 50...

Adhesive Dispensing Gun with 10:1 Plunger for AT-6030 Adhesive OnlyThe AT- 301 Adhesive Dispensing Gun Is Designed Specifically For Use With Our AT-6030 38 ml 10:1 Adhesive Cartridge. This Hand Operated Gun And Our Mixing Tips Provide Precise Mixing And Dispensing Of Our Adhesives....

Titanium Adjustable WrenchAdjustable Wrench-CNC-machined from a solid block of Grade 5 billet titanium, engineered to take on relentless saltwater abuse without rusting, bending, or breaking down.Designed with an extra-wide jaw that opens up to 1", it's large enough to remove a prop nut and...

Titanium Prop Nut Socket 1-1/16" - 1/2" DriveUpgrade your tool kit with our Grade 5 Titanium Prop Nut Socket—built for serious performance in the harshest marine environments. Precision-machined from aerospace-grade Ti-6Al-4V (Grade 5) titanium, this socket delivers exceptional strength with a lightweight feel, while...

Titanium Prop Nut Socket Mercury V10Upgrade your tool kit with our Grade 5 Titanium Prop Nut Socket - built for serious performance in the harshest marine environments. Precision-machined from aerospace-grade Ti-6Al-4V (Grade 5) titanium, this socket delivers exceptional strength with a lightweight feel, while...

White Nylon Wire Tie MountThe AT-5 tie mount is designed to be set into wet resin during the hull lay up or bonded with our acrylic adhesives. It's designed for a #5 wire tie and has an average pull strength of 150 lbs. It's...